Author |
Topic |
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/11/2017 : 09:58:01 AM
|
on this one with the tail lights on and turn signal on the tail lights flicker where the turn signal flashes i figured its a ground issue check grounds they are good when i put my power probe on the tail light voltage wire i get a pulse when the turn signal flashes is there a turn signal flasher or does it run threw the multiplex unit???? |
|
RonF
Top Member
867 Posts |
Posted - 07/12/2017 : 04:19:41 AM
|
It runs through the multi-plex box. |
US Army retired CMBT |
|
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/12/2017 : 05:04:14 AM
|
when i test the tail light wire coming out of the multiplex it pulse i am thinkin a bad multiplex unit ?? |
|
|
RonF
Top Member
867 Posts |
Posted - 07/12/2017 : 08:52:08 AM
|
Check it going in and see if it pulses, which it shouldn't. If not bad box. |
US Army retired CMBT |
|
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/12/2017 : 09:52:20 AM
|
its ground coming in from switch and thats steady i swaped out the box with another one and same thing i cleaned grounds at all lights the monitor and still flashed only way it stops is if i take all the bulbs tturn signal bulb from front and rear it stops pulsing the tail lights with only the four side body lights flashing |
|
|
torque
Advanced Member
Canada
358 Posts |
Posted - 07/13/2017 : 10:03:14 AM
|
I dont have a schematic in front of me, but if I remember correctly, the clearance light work as follows, ground signal from the switch, to the multiplex, from there the signal goes to the relay in the side panel, and the power that goes to the tail lights, gets its power from the fuse panel on the side, not directly from the multiplex, so you would want to check your power at that relay? See what happens there |
|
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/14/2017 : 11:12:29 AM
|
u wouldnt happen to no what relay iit is there are alot |
|
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/14/2017 : 11:27:31 AM
|
i found the relay and the power pulses there to i swapped to see what happens no change again with lights on and four ways on the tail lights flicker everytime the signals flash the ground is good from switch to multiplex but the signal out to tail lights pulse right at the connecter when signals are on i swapped the multiplex thinkim it was that i checked all grounds to rear tails i am lost here seems like a ground issue |
|
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/17/2017 : 05:10:32 AM
|
would anyone have a wiring diagram for the tail lights and turn signals |
|
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/17/2017 : 05:21:17 AM
|
alsoi notice that the horn signal has a slight flicker in it as well i really need a wiring diagram to see whats what does anyone have one i cant find one and there is no flasher correct????? |
Edited by - dsalinas1939 on 07/17/2017 05:22:43 AM |
|
|
RonF
Top Member
867 Posts |
Posted - 07/17/2017 : 05:28:13 AM
|
You don't have access to BLue Bird vantage? It is free if you have purchase blue bird buses. Contact your dealer and they can set you up within hours. Vantage has everything manual wise for your specific bus. |
US Army retired CMBT |
|
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/17/2017 : 05:37:03 AM
|
no we dont have that we only have to visions and never got it will look into it
|
|
|
torque
Advanced Member
Canada
358 Posts |
|
dsalinas1939
Top Member
USA
1324 Posts |
Posted - 07/19/2017 : 07:30:57 AM
|
thanks guys i got the diagram didnt have to login i ended up cleaning the main power wires to the multiplex they had some kinga plastic melted in there it helped with the loss of voltage to the multiplex the lights still flicker but alot better u really have to stare at them to see gonna see if thats good enought to go threw inspection no idea what else could be the problem if it goes threw which i think it will i will have to go threw all the power wires and clean up |
|
|
|
Topic |
|