Why the industry should retire Dayton-style wheels

Paul Cochran
Posted on March 1, 1999

Although the vast majority of today's school buses are spec'd for Budd-style disc wheels, some fleets still prefer the Dayton-style spoke wheel. And, yes, chassis are still being manufactured with the cast spoke wheel. They continue to come down the line at some of the country's largest school bus manufacturers. This is puzzling. Although spoke wheels used to be much less expensive than disc wheels, the pricing is very similar these days. And, by all accounts, the Dayton-type wheel is inferior to the Budd-style wheel in many ways, particularly in regard to safety. Spoke wheels go by many different names, such as "military wheels," "West Coast wheels," "widow makers" and "spider wheels." They are split rims with one or two lock rings.

Potential hazard for mechanics
I'm sure you have all heard horror stories about mechanics who failed to properly seat the lock rings, resulting in the loss of a hand or the rings getting stuck in the shop roof. You don't have that potential endangerment with the disc wheel because assembly error doesn't come into play. Dayton wheels with multipiece rims also have the potential to blow apart as the vehicle is traveling down the highway. Needless to say, this could create hazardous situations for the bus driver, his passengers and other motorists. Serviceability is another prime consideration when comparing the Dayton wheel with the Budd wheel. It takes more time and skill to remove and install a spoke wheel. If you don't remove them properly, you may end up with a rim clamp hitting you between the eyes when the wheel releases. In addition, it's much more time consuming to reline brakes with Dayton wheels because you have to pull the axles and hubs, which can damage increasingly expensive seals and gaskets. With the Budd wheel, you only have to pull the wheel assemblies and brake drum to reline the brakes. The Budd wheel brake procedure reduces labor costs as well as parts costs. Another point to consider is wheel alignment. Unless the Dayton wheel's lugs are evenly tightened, the unit may not run "true," meaning that the front or rear wheels could wobble. This wobble not only reduces the performance of the vehicle, it may also lead other motorists to believe that the wheels are loose. This misunderstanding harms the image of the school district or contractor operating the bus and is an inconvenience for conscientious motorists who take the time and effort to report the wobble to the bus operator.

Better tire options with disc
A final consideration is the availability of tires for the Dayton-style wheel. It's getting more and more difficult to locate tube tires for the spoke-style split rims and the cost of tube types is increasing substantially. The industry has solidly embraced tubeless radial tires because they are less expensive, have longer tread life and provide better handling than their tube counterparts. So why would fleet managers continue to spec Dayton-style wheels on their school buses? It may be that the existing fleet has spoke wheels and standardization is a priority. Or it may be that cost pressures are so intense that any area for savings is embraced. It's only a matter of time, however, before the entire industry will embrace the disc wheel. Based on what I've heard and seen, the sooner, the better.

Paul Cochran is fleet maintenance supervisor at Kyrene School District in Tempe, Ariz.

Related Topics: tires/wheels

Comments ( 1 )
  • John Doe

     | about 4 years ago

    The author doesn't have a complete understanding of the subject. One-piece Dayton rims are readily available for tubeless tires. These one-piece rims DO NOT have lock rings, and obviously they're not "split" rims. Pretty much everything he says is pretty much invalid. The only valid point he made was regarding brake servicing - yes, it's quite a bit easier to service brakes with Budd-style wheels. But how often do brakes get serviced? I'm not familiar with school bus service routines, but I'm sure it's not a daily, weekly, or even monthly event...

More Stories

King Pin Pusher Set

OTC’s new 30-Ton King Pin Pusher Set is designed to assist technicians when changing king pins and brake anchor pins on heavy-duty vehicles.


Portable Magnetometer

The FerroCheck 2000 series of portable magnetometers is designed to quickly and conveniently measure total ferrous wear particulates in lubricating fluids.


Commercial Vehicle Application Catalog

Raybestos’ new Commercial Vehicle Application Catalog and Specification Guide (BPI-CV17) is designed to help fleet managers and professional service technicians meet the demands of maintaining and repairing commercial vehicles.


PACCAR Parts Opens 100th TRP Store

The new TRP location in Alexandria, Louisiana, will offer the brand’s aftermarket replacement parts for trucks, trailers, and buses.

Be the First to Know

Get the latest news and most popular articles from SBF delivered straight to your inbox. Stay on top of the school bus industry and don't miss a thing!