Subscribe Today

December 02, 2013  |   Comments (4)   |   Post a comment

New standards target stronger wheelchair tie-downs, increased safety


SHARING TOOLS   | Email Print RSS
To comply with the new WC18 standard, wheelchair tie-downs or other securement devices must pass two different dynamic strength tests.

To comply with the new WC18 standard, wheelchair tie-downs or other securement devices must pass two different dynamic strength tests.

New safety standards for wheelchairs and tie-downs promise to improve transportation safety for people who must use their wheelchair as the passenger seat when riding in a car, van or bus.

Some of these new product design and crash test requirements have already gone into effect, while additional ones will not be in effect until December 2015. In advance of this deadline, innovators of wheelchair tie-down systems are already striving to implement upcoming safety improvements for today’s passengers.

To comply with the new industry standards published in Wheelchairs and Transportation, Volume 4, of RESNA (Rehabilitation Engineering and Assistive Technology Society of North America) wheelchair standards — commonly referred to as WC18 — wheelchair tie-downs or other securement devices must pass two different dynamic strength tests.

Both of the impact sled tests subject the tie-downs to a 30 mph, 20-g crash using a “surrogate” wheelchair and average weight dummy. What differs between the first test requirements that are already in effect and those requirements coming in December 2015 is how the occupant belts are installed.

In the current WC18 requirement, the lap and shoulder belt is installed in such a way that the entire load of the occupant is applied to the vehicle during impact, effectively separating the wheelchair and occupant loads from each other.

The second test requirement, as stated in WC19, places the occupant’s lap belt onto the wheelchair frame itself, therefore transferring a majority of that force onto the tie-downs, thus providing additional safety to the passenger.

The previous standards were implemented in 2002, and RESNA’s recent changes to both the WC18 and WC19 standards reflect 10 years of real-world experience of passengers, wheelchairs and securement systems in both crash and non-crash events.

Building on the success of the previous requirements, the new standards will provide additional precautions based on today’s transportation environments to further ensure passenger safety. Lessons learned from the past 10 years have reinforced the need for an anchored lap belt for providing a safe and respectful transportation experience for the wheelchair-dependent passenger.

Among its many benefits, the wheelchair-anchored lap belt:

• Provides a better fit low on the passenger’s pelvis, the safest and most secure belt location;

• Eliminates interference from wheelchair components such as armrests, as can happen with a lap belt anchored to the vehicle floor;

• Reduces invasion of the passenger’s personal space by the vehicle operator or other attendant who would otherwise be securing straps around the passenger’s body because the passenger would already be wearing the belt;

• Reduces the time required to secure the lap-shoulder belt.

These benefits address not only improved passenger safety, but also a more efficient and independent securement process. Thus, manufacturers see real value for their customers, and riders and drivers alike are eager to see the new improvements implemented rapidly.

“The revised standards pose a design challenge; however, we recently announced our new QRT-360 retractor that is fully compliant with the WC18 standard and will be available early 2014,” said Bob Joseph, vice president of business development at Florida-based securement systems manufacturer Q’Straint. “Q’Straint is pleased to offer improved wheelchair restraint safety to passengers well ahead of the December 2015 deadline.”

This article was submitted by Q'Straint.


Post a Comment

Read more about: wheelchairs


For a heavy chair/occupant,Place the restraints behind one another in the middle tracks. In other words, two restraints on each middle track back to back.

John Welsh    |    Mar 11, 2014 10:53 AM

I have a question is it legal or wise to criss cross the back tie downs on the back of a wheelchair as back up ones on a heavier chair? I'm being told this is ok when all videos say to never do this for a wheelchair may buckle on an impact due to criss crossing.

wendy    |    Mar 07, 2014 07:25 PM

Does anyone know if old ones will be grandfathered in or will everyone have to purchase the new ones?

Diane Fleming    |    Dec 10, 2013 05:49 AM

I really like the change with the lap belt, I never have liked the across the arms of the chair.

Estelle Ellis    |    Dec 09, 2013 03:46 PM

Post a comment





Related Stories

Premium Member

Get bus sales numbers, transportation statistics, bus specifications, industry survey results, bus loading and unloading fatality statistics and more in the School Bus Fleet Research Center. Become a premium member today!
Log in Button Register Button

Newsletter

Get breaking news, industry updates, product announcements and more.