Subscribe Today

August 01, 2002  |   Comments (1)   |   Post a comment

Do School Buses Need Additional Warning Devices?

School bus loading or unloading near intersections may not be visible to motorists approaching from an angle. Additional or improved warning systems would help to alert motorists of the need to slow down and stop.

by Tim Parker


SHARING TOOLS   | Email Print RSS

The familiar yellow school bus is rightfully touted as being the safest vehicle on the road. But, is it as safe as it should be? Do we, the people who use, maintain and build school buses, create a problem when we stop looking for ways to make it safer? Passengers are protected by a design of steel and padding that is unsurpassed in the level of safety provided. There are always other things that can be added that may improve safety, but, overall, it's a safe environment inside the bus. However, when passengers are outside the bus, particularly when they must cross the street, there are limitations to the safety that can be ensured. Why don't motorists stop?
Transportation supervisors make every effort to route buses to limit the need for students to cross streets. Many make efforts to avoid pick-ups at intersections where a motorist may be less likely to see the red lights, stop arms and crossing gates of a school bus that is loading or unloading. We teach our students about the "danger zones" and the need to use extra caution when crossing streets. But once they are outside the bus, we are in large part relying on students, patrols, monitors, parents and motorists to watch and provide protection. No one in his right mind would intentionally harm children by striking them with a vehicle, but every year several young bus passengers are struck by motorists passing the big yellow bus with all of its warning devices in operation. In some cases, motorists are unconcerned with or ignorant of motor vehicle laws. In other cases, motorists genuinely fail to realize that a bus is stopped to load or unload, often due to inadequate warning systems or blind spots. But wouldn't they see the stop arm as they approach? Typically, yes. But not always.

A blind spot in "the zone"
The problem is that current warning devices are principally directed at traffic approaching from the front or rear. Despite efforts to avoid placing bus stops at intersections where traffic approaches from the side, loading and unloading near intersections still happens too frequently. Motorists approaching a bus from the side do not get sufficient warning that the bus is stopped to load or unload passengers. They can see a yellow bus stopped at an intersection, but what tells them that the bus is loading or unloading or that children may be crossing? Buses stop or pause at intersections to check traffic before turning or crossing intersections more frequently than they do to load or unload passengers. To assume that approaching motorists will see a child in their path is dangerous. Bus drivers are protective of their passengers and use signals to tell students when to cross, but this is not sufficient. It's true that many buses have crossing arms that might act as a warning for motorists to stop. We know what a crossing arm means, but will a motorist see it at its low height or understand its meaning? It is crucial that we modify our current warning system components or require something additional that alerts motorists approaching from the side of the need to stop. Existing components like red warning lights, strobes or signs could be re-engineered to catch the eye of a motorist approaching the bus from the right or the left side. The need for improved warning systems is particularly urgent toward the front of the bus, where the vehicle often protrudes into the intersection. One possible solution is to re-engineer existing bus components to make them part of the warning system — marker lights that flash, re-designed warning lights on top of the bus like on emergency vehicles or redesigned stop arms that provide more side illumination. Although electrical systems are already strained, LED technology can reduce the electrical power demands on buses, allowing for additional or improved lights. Police lights set example
Police and fire vehicles started with a single red directional light. This system was increased to two lights, with one aimed to the front and one to the rear. Then a round, multi-directional light was added to the roof for greater visibility. Now that system has evolved into a large, multi-directional bar light for added safety and recognition. School bus lighting systems started much the same way, but have evolved differently - from the single red light to two lights (one aimed to the front and one to the rear), to three and four lights and then finally to eight-lamp systems with both amber and red. When motorists still did not stop, we added stop arms on the side to catch their attention as they started to pass. Some states even began to allow roof-mounted amber or white strobe lights to provide additional visibility in inclement weather or on high-speed highways. Much effort has been made to standardize school bus equipment and make buses universally recognizable for the safety of our children. The distinct and uniform yellow color and lighting systems were major national steps for our industry. True, major lighting system changes could confuse some motorists. Maintenance and procurement costs would increase as well. But we cannot afford to be restricted by the past when change is needed. Whether it is a replacement of the familiar single-direction warning light system with a multi-directional system (as seen on police vehicles) or whether it is a slight modification of what we have now, we must look for what is best for the future of the school bus. Too costly not to act
Should we simply supplement the existing warning system with additional lights aimed to the side, or should we be bolder? Would school buses become more recognizable at bus stops, and would the message for motorists to stop be clearer if the bus was equipped with a multi-directional amber and red bar light instead of our traditional fixed-direction lights? Review your designated bus stop locations, and look where the buses are actually stopping to load or unload on the road. The difference of a few feet can make a big difference in safety. Unless you can avoid having bus stops at intersections, you cannot be silent on this issue. There are blind spots to be fixed and, to avoid putting children at risk, your intervention is needed. Look for solutions and encourage changes as appropriate. There may be simple solutions available. Discuss this with your drivers, garage staff, state inspectors, state directors and manufacturers, and share what you learn.

Industry Input

The following responses were drawn from the Forum at www.schoolbusfleet.com

I don't believe that additional warning lights on school buses are going to stop those persons who run our lights. Some people can't be bothered by stopping for a school bus that is loading or unloading children. You could light the bus up like a Christmas tree and these people wouldn't care.
STEVE LOWER
School Bus Driver
Norman (Okla.) Public Schools

Anything that can make stops safer is welcome. I believe most people who run bus lights simply don't see them. I've honked at drivers who don't slow down and seen them display surprise that I'm there. A good idea would be an audible alarm for cars that approach an unloading school bus too fast — one that's loud enough to wake the dead.
DAVE COBB
School Bus Driver
Austin, Texas

At some point, all kids riding buses need to be trained by the driver how to watch out for themselves and their friends. Training the kids, a daily routine, does not guarantee a child won't make a mistake. Bus drivers and motorists make deadly mistakes, regardless of their training. It would be dumb to think all kids would get it right every time, but equally dumb to use this as an excuse not to train the kids in safe practices.
JAMES KRAEMER
Director
www.2safeschools.org

Rather than adding anything more to school buses, maybe we should start thinking about regulating where a bus stop should be. A corner where motorists will be turning in and out is not very logical. Getting off of the roadway, which would interfere with the directional red light system, does not seem to be a wise decision either. A school bus that remains visible to the public and allows room for motorists to leave or enter side streets without blocking visibility is the first part of a safe stop. Driver training is another important link. The third part would be making sure to have a safe walk plan to and from the stop, with parents made aware of their responsibility to train their children in appropriate behavior.
MERLE JEWETT
Transportation Director
Merced (Calif.) City School District


Post a Comment

Read more about: danger zone, stop arm running/illegal passing

Request More Info about this product/service/company

I aagree that school buses often board or discharge students near minor type intersections that lack traffic signal control. In my home Province, Ontario in Canada it is unlawfull to operate the buses' overhead red signals (aka: schooler lights) positioned less than 200 feet or 60 metres from a traffic signal controlled corner At the others I have had motorists occasionally overlook the schooler reds. That is why having your students rigidly trained to watch for this is important. In the majority of cases the motorists act shocked and too late comply when the bus horn is honked as a danger alert. . I believe its often a case of their mind just being elsewhere, so extra strobes (red or amber) or brilliant extra flashing LEDS may not over come this dangerous and irritating, but thankfully rare problem.

Mike Gough    |    Aug 30, 2010 12:53 PM

Post a comment





Related Stories

Premium Member

Get bus sales numbers, transportation statistics, bus specifications, industry survey results, bus loading and unloading fatality statistics and more in the School Bus Fleet Research Center. Become a premium member today!
Log in Button Register Button

Newsletter

Get breaking news, industry updates, product announcements and more.